[Modified QuEChERS method combined with ultra performance liquid chromatography-tandem mass spectrometry for detection of cyclopiazonic acid in feeds].

Mycotoxins are toxic secondary metabolites produced by fungal species that can cause acute, subacute, and chronic toxicity in humans and animals. Thus, these toxins pose a significant threat to health and safety. Owing to the lack of effective antimold measures in the agricultural industry, feed ingredients such as corn, peanuts, wheat, barley, millet, nuts, oily feed, forage, and their byproducts are prone to mold and mycotoxin contamination, which can affect animal production, product quality, and safety. Cyclopiazonic acid (CPA), which is mainly biosynthesized from mevalonate, tryptophan, and diacetate units, is a myotoxic secondary metabolite produced by Penicillium and Aspergillus fungi. CPA is widely present as a copollutant with aflatoxins in various crops. Compared with some common mycotoxins such as aflatoxins, fumonisins, ochratoxins, zearalenones, and their metabolites, CPA has not been well investigated. In the United States, a survey showed that 51% of corn and 90% of peanut samples contained CPA, with a maximum level of 2.9 mg/kg. In Europe, CPA was found in Penicillium-contaminated cheeses as high as 4.0 mg/kg. Some studies have shown that CPA can cause irreversible damage to organs such as the liver and spleen in mice. Therefore, the establishment of a rapid and efficient analytical method for CPA is of great significance for the risk assessment of CPA in feeds, the development of standard limits, and the protection of feed product quality and safety. The QuEChERS method, a sample pretreatment method that is fast, simple, cheap, effective, and safe, is widely used in the analysis of pesticide residues in food. In this study, a modified QuEChERS method combined with ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) was used to determine CPA levels in feeds. The chromatographic separation and MS detection of CPA as well as the key factors affecting the extraction efficiency of CPA, including the type of extraction solvent, type of inorganic salt, and type and dosage of adsorbent, were optimized in detail. During the optimization of the chromatographic-separation step, the acid and salt concentrations of the mobile phase affected the separation and detection of CPA. During the optimization of the QuEChERS method, the addition of a certain amount of acetic acid improved the extraction efficiency of CPA because of its acidic nature; in addition, GCB and PSA significantly adsorbed CPA from the feed extract. Under optimal conditions, the CPA in the feed sample (1.0 g) was extracted with 2 mL of water and 4 mL of acetonitrile (ACN) containing 0.5% acetic acid. After salting out with 0.4 g of NaCl and 1.6 g of MgSO4, 1 mL of the ACN supernatant was purified by dispersive solid-phase extraction using 150 mg of MgSO4 and 50 mg of C18 and analyzed by UPLC-MS/MS. The sample was separated on a Waters HSS T3 column (100 mm×2.1 mm, 1.8 µm) using 2 mmol/L ammonium acetate aqueous solution with 0.5% formic acid and ACN as the mobile phases and then analyzed by positive electrospray ionization in multiple reaction monitoring mode. CPA exhibited good linearity in the range of 2-200 ng/mL, with a high correlation coefficient (r=0.9995). The limits of detection and quantification of CPA, which were calculated as 3 and 10 times the signal-to-noise ratio, respectively, were 0.6 and 2.0 µg/kg, respectively. The average recoveries in feed samples spiked with 10, 100, and 500 µg/kg CPA ranged from 70.1% to 78.5%, with an intra-day precision of less than 5.8% and an inter-day precision of less than 7.2%, indicating the good accuracy and precision of the proposed method. Finally, the modified QuEChERS-UPLC-MS/MS method was applied to the analysis of CPA in 10 feed samples obtained from Wuhan market. The analysis results indicated that the developed method has good applicability for CPA analysis in feed samples. In summary, an improved QuEChERS method was applied to the extraction and purification of CPA from feeds for the first time; this method provides a suitable analytical method for the risk monitoring, assessment, and standard-limit setting of CPA in feed samples.

[Progress in the application of novel nano-materials to the safety analysis of agricultural products].

The quality and safety of agricultural products are strongly related to human livelihood. Thus, the government and consumers have recently paid increased attention to the quality and safety of agricultural products. The development of efficient, rapid, and sensitive analytical methods for detecting pesticides, veterinary drugs, heavy metals, mycotoxins, and environmental pollutants in agricultural products is of great significance. Owing to the complexity of many sample matrices and the low concentration of pollutants in a typical sample, appropriate sample pretreatment steps are necessary to enrich pollutants in agricultural products. Solid-phase extraction (SPE) is the most widely used sample pretreatment technology; in this technique, the adsorbent generally determines the selectivity and efficiency of the extraction process. An increasing number of novel materials have been used as SPE adsorbents. The extraction efficiency, extraction selectivity, and analytical throughput of SPE could be greatly improved by combining these novel materials with various extraction modes (e. g., solid-phase microextraction, dispersed SPE, and magnetic SPE (MSPE)) during sample preparation. Because of their large specific surface area and high affinity toward target analytes, nanomaterials are often used as SPE adsorbents, thereby greatly improving the selectivity and sensitivity of the analytical technology. More importantly, these materials have become a priority area of research on preconcentration technologies for trace compounds in agricultural products. This paper summarizes the adsorption characteristics of several new nanomaterials, including magnetic materials, carbon-based materials, metal nanomaterials (MNs), metal oxide nanomaterials (MONs), metal organic frameworks (MOFs), and covalent organic frameworks (COFs). These nanomaterials present numerous advantages, such as large specific surface areas, high adsorption capacities, and tailorable structural designs. MSPE employs magnetic materials as sorbents to afford fast dispersion and efficient recycling when applied to complex sample matrices under an external magnetic field. The use of MSPE can avoid several typical problems associated with SPE such as poor adsorbent packing and high pressure, thereby greatly simplifying the pretreatment process and providing a high flux for sample analysis. Carbon-based materials are powdered or bulk nonmetallic solid materials with carbon as the main component; carbon and nitrogen materials, mesoporous carbon, carbon nanotubes, and graphene are some examples of these materials. These materials provide large specific surface areas, abundant pore structures, good thermal stability, high mechanical strength and adsorption capacity, and controllable morphology. Pure and modified carbon nanomaterials have been successfully used to purify target analytes from agricultural products. Given their unique physical and chemical properties, MNs and MONs have attracted significant interest for use in sample preparation. MNs and MONs with excellent thermal and mechanical stabilities show good resistance to a wide pH range and diverse organic solvents, which is crucial in adsorbent-based extraction methods. The surface of these materials can be easily modified with various ligands to improve their selectivity. MOFs and COFs present many advantages such as large specific surface areas, high porosity, adjustable pore performance, and good thermal stability. Several methods that employ novel adsorbent materials to analyze pollutants in a variety of agricultural products, such as chromatography, spectroscopy, mass spectrometry, and other detection technologies, have been established. This paper also reviews the application of adsorbent materials in the analysis of agricultural product quality and safety, and discusses the future development trends of these sorbents in sample preparation for the safety analysis of agricultural products.

Application of a novel nylon needle filter-based solid-phase extraction device to determination of 1-hydroxypyrene in urine.

In this work, a simple and miniaturized solid-phase extraction device was constructed by connecting a commercial nylon needle filter to a syringe, which was applied for extracting 1-hydroxypyrene from a urine sample via hydrophobic and hydrogen bond interactions. The nylon membrane in the needle filter acted as the solid-phase extraction adsorbent, meanwhile, it filtered the particles in the urine sample. To obtain high extraction efficiency, key parameters influencing extraction recovery were investigated. The entire pretreatment process was accomplished within 5 min under the optimal conditions. By coupling high-performance liquid chromatography-ultraviolet, a rapid, low-cost, and convenient nylon needle filter-based method was established for the analysis of 1-hydroxypyrene in a complex urine matrix. Within the linearity range of 0.2-1000 µg/L, the method exhibited a satisfactory correlation coefficient (R = 0.9999). The limit of detection was 0.06 µg/L, and the recoveries from urine sample spiked with three concentrations (5, 20, and 100 µg/L) ranged from 105.8% to 113.1% with the relative standard deviations less than 6.7% (intra-day, n = 6) and 8.9% (inter-day, n = 4). Finally, the proposed method was successfully applied for detecting 1-hydroxypyrene in urine samples from college students, smokers, gas station workers, and chip factory workers. The detected concentration in actual urine samples ranged from 0.46 to 5.26 µg/L. Taken together, this simple and cost-effective nylon needle filter-based solid-phase extraction device showed an excellent application potential for pretreating hydrophobic analytes from aqueous samples.

Rapid and Sensitive Detection of Aflatoxin B1, B2, G1 and G2 in Vegetable Oils Using Bare Fe3O4 as Magnetic Sorbents Coupled with High-Performance Liquid Chromatography with Fluorescence Detection.

This paper reports a simple, sensitive and reliable method for the simultaneous detection of aflatoxin B1, B2, G1 and G2 in vegetable oils. Aflatoxins were extracted by magnetic solid phase extraction followed by high-performance liquid chromatography, then postcolumn photochemical derivatization and finally detected by fluorescence detector. Vegetable oil samples were first diluted with hexane and then commercial bare Fe3O4 nanoparticles were directly employed as sorbents to extract aflatoxins from complex vegetable oil samples, which significantly simplified the procedure of sample preparation and largely improved the sample analysis throughput. The effects of various parameters such as the amount of sorbent, loading, washing and eluting conditions were carefully optimized to improve the extraction efficiencies of aflatoxins. Under the optimal conditions, the limits of detection of four aflatoxins ranged from 0.01 µg/kg to 0.16 µg/kg, and squared regression coefficients (R2) >0.9990 were obtained within the linear range of 0.1-20 µg/kg (except for aflatoxin G2 with 0.5-20 µg/kg). Furthermore, the recoveries spiked at four concentration levels in a blank vegetable oil sample were from 82.6 to 106.2%, with inter- and intraday relative standard deviations <9.8%, indicating good accuracy and precision of the proposed method.

Rapid and sensitive detection of the phenoxy acid herbicides in environmental water samples by magnetic solid-phase extraction combined with liquid chromatography-tandem mass spectrometry.

Phenoxy acid herbicides are widely used herbicides that play an important role in improving the yield and quality of crops. However, some research has shown that this kind of herbicide is poisonous to human and animals. In this study, a rapid and sensitive method was developed for the detection of seven phenoxy acid herbicides in water samples based on magnetic solid-phase extraction followed by liquid chromatography and tandem mass spectrometry. Magnetic amino-functionalized multiwalled carbon nanotubes were prepared by mixing bare magnetic Fe3 O4 nanoparticles with commercial amino-functionalized multiwalled carbon nanotubes in water. Then the amino-functionalized multiwalled carbon nanotubes were used to enrich phenoxy acid herbicides from water samples based on hydrophobic and ionic interactions. The effects of experimental variables on the extraction efficiency have been studied in detail. Under the optimized conditions, the method validation was performed. Good linearities for seven phenoxy acid herbicides were obtained with squared regression coefficients ranging from 0.9971 to 0.9989. The limits of detection ranged from 0.01 to 0.02 µg/L. The method recoveries of seven phenoxy acid herbicides spiked at three concentration levels in a blank sample were from 92.3 to 103.2%, with inter- and intraday relative standard deviations less than 12.6%.

Rapid and sensitive detection of fipronil and its metabolites in edible oils by solid-phase extraction based on humic acid bonded silica combined with gas chromatography with electron capture detection.

Solid-phase extraction based on humic acid bonded silica followed by gas chromatography with electron capture detection was developed to determine fipronil and its metabolites in edible oil. To achieve the best extraction performance, we systematically investigated a series of solid-phase extraction parameters. Under the optimized conditions, the method was validated according to linearity, recovery, and precision. Good linearities were obtained with R(2) more than 0.9996 for all analytes. The limits of detection were between 0.3 and 0.5 ng/g, and the recoveries ranged from 83.1 to 104.0% at three spiked concentrations with intra- and interday relative standard deviation values less than 8.7%. Finally, the proposed method was applied to determine fipronil and its metabolites in 11 edible oil samples taken from Wuhan markets. Fipronil was detectable in four samples with concentrations ranging from 3.0 to 5.2 ng/g. In China, the maximum residue limits of fipronil in some vegetables and maize are 20 and 100 ng/g (GB/T 2763-2014), respectively. The residues of fipronil and its metabolites in commercial edible oils might exhibit some potential threat to human health as a result of high consumption of edible oil as part of daily intake.

Preparation and chromatographic evaluation of zwitterionic stationary phases with controllable ratio of positively and negatively charged groups.

The present study described the preparation and application of zwitterionic stationary phases (ACS) with controllable ratio of positively charged tertiary amine groups and negatively charged carboxyl groups. Various parameters, including water content, pH values and ionic strength of the mobile phase, were investigated to study the chromatographic characteristics of ACS columns. The prepared ACS columns demonstrated a mix-mode retention mechanism composed of surface adsorption, partitioning and electrostatic interactions. The elemental analysis of different batches of the ACS phases demonstrated good reproducibility of the preparation strategy. Additionally, various categories of compounds, including nucleosides, water-soluble vitamins, benzoic acid derivatives and basic compounds were successively employed to evaluate the separation selectivity of the prepared ACS stationary phases. These ACS phases exhibited entirely different selectivity and retention behavior from each other for various polar analytes, demonstrating the excellent application potential in the analysis of polar compounds in HILIC.

Preparation of mesoporous ZrO2-coated magnetic microsphere and its application in the multi-residue analysis of pesticides and PCBs in fish by GC-MS/MS.

A novel mesoporous ZrO2 immobilized magnetic Fe3O4 microsphere (m-ZrO2@Fe3O4) was successfully synthesized and characterized by transmission electron microscope (TEM), X-ray diffractometer (XRD), nitrogen adsorption measurement (NAM), energy-dispersive X-ray analysis (EDX), vibrating sample magnetometer (VSM). Then the resultant m-ZrO2@Fe3O4 and an n-octadecylphosphonic acid modified magnetic microsphere (Fe3O4-OPA) were employed as clean-up co-adsorbents of QuEChERS (Quick, Easy, Cheap, Effective, Rugged, Safe) method for the analysis of 42 pesticides and 7 polychlorinated biphenyls (PCBs) in fish samples. Lipid co-extractives such as fatty acids in QuEChERS extracts could be efficiently removed through the Lewis acid-Lewis base interaction between m-ZrO2@Fe3O4 and carboxylic groups, while some other apolar interferents could be adsorbed through hydrophobic interaction by Fe3O4-OPA. Meanwhile, the magnetic property of adsorbents endows the clean-up procedure with manipulative convenience. Several parameters affecting the clean-up performance were investigated. Under the optimal conditions, the modified QuEChERS method combined with gas chromatography-tandem mass spectrometry (GC-MS/MS) for the multi-class, multi-residue analysis of pesticides and PCBs in fish samples was validated according to linearility, recovery and precision. Good linearities were obtained for all analytes with R(2) larger than 0.9903. Limits of detection (LODs) were found to be in the range of 0.02-4.40 ng/g. The method recoveries of all analytes spiked at three concentration levels in blank fish samples were from 69.8% to 117.1%, with the intra-day and inter-day relative standard deviations (RSDs) less than 13.4% and 16.5%, respectively.

Preparation and chromatographic evaluation of a novel phosphate ester-bonded stationary phase with complexation and hydrophobic interactions retention mechanism.

The present study described the preparation of a novel phosphate ester-bonded silica (PES) stationary phase based on "thiol-ene" click chemistry. The composition of the surface grafts of PES stationary phase was determined by elemental analysis and solid state (31)P MAS NMR. Due to its hydrophilic phosphate-ester groups and short hydrophobic alkyl chains, the PES stationary phase exhibited dual retention mechanism via complexation and hydrophobic interactions with phenols. Benefiting from this special interaction mechanism, the newly synthesized PES stationary phase showed better selectivity in the separation of phenols compared to commercial octadecylsilyl-bonded silica (C18) columns. Furthermore, the separations of 10 nucleosides and nucleobases on the PES stationary phase were achieved in both reversed-phase liquid chromatography (RPLC) mode and hydrophilic interaction liquid chromatography (HILIC) mode.

Preparation of a novel carboxyl stationary phase by "thiol-ene" click chemistry for hydrophilic interaction chromatography.

A novel carboxyl-bonded silica stationary phase was prepared by "thiol-ene" click chemistry. The resultant Thiol-Click-COOH phase was evaluated under hydrophilic interaction liquid chromatography (HILIC) mobile phase conditions. A comparison of the chromatographic performance of Thiol-Click-COOH and pure silica columns was performed according to the retention behaviors of analytes and the charged state of the stationary phases. The results indicated that the newly developed Thiol-Click-COOH column has a higher surface charge and stronger hydrophilicity than the pure silica column. Furthermore, the chromatographic behaviors of five nucleosides on the Thiol-Click-COOH phase were investigated in detail. Finally, a good separation of 13 nucleosides and bases, and four water-soluble vitamins was achieved.

Preparation of phenothiazine bonded silica gel as sorbents of solid phase extraction and their application for determination of nitrobenzene compounds in environmental water by gas chromatography-mass spectrometry.

In this paper, two phenothiazine bonded silica (PTZ-Si) sorbents were prepared and used as sorbents of solid-phase extraction (SPE) for the determination of nitrobenzene compounds in environmental water samples by gas chromatography-mass spectrometry (GC-MS). Different synthesis routes were proposed to obtain high bonded amount of PTZ on the surface of silica gel. PTZ molecule was derived to its amino or acyl chloride derivatives for reacting with isocyanate or amino silane coupling agent, which was further reacted with the surface silanol groups of silica gel to obtain the PTZ-Si sorbents. The resultant PTZ-Si sorbents were characterized by nitrogen sorption porosimetry (NSP), Fourier transform infrared spectroscopy (FT-IR) and elemental analysis (EA) to assure the successful bonding of PTZ on the surface of silica gel. Then the PTZ-Si sorbents were served as SPE sorbents for the enrichment of nitrobenzene compounds. Several parameters affecting the extraction performance were investigated. Under the optimized conditions, the proposed method was applied to the analysis of six nitrobenzene compounds in environmental water samples. Good linearities were obtained for all nitrobenzene compounds with R(2) larger than 0.9958. The limits of detection were found to be in the range of 0.06-0.3 ng/mL. The method recoveries of nitrobenzene compounds spiked in water samples were from 71.4% to 124.3%, with relative standard deviations (RSDs) less than 10.1%.

Grafting of silica with a hydrophilic triol acrylamide polymer via surface-initiated "grafting from" method for hydrophilic-interaction chromatography.

A novel hydrophilic polymer-coated silica sorbent has been prepared using the radical "grafting from" polymerization method through surface-bound azo initiators for hydrophilic-interaction chromatography (HILIC). The azo groups were introduced to the surface of silica gel through the reaction with amino groups on the surface of silica gel with 4,4'-azobis(4-cyanopentanoic acid chloride) (ACVC). The resultant azo-immobilized silica gel served as surface initiator to polymerize hydrophilic triol acrylamide monomer N-acryloyltris(hydroxymethyl) aminomethane (NA) in methanol to get hydrophilic polymer-coated silica sorbent. The obtained poly(NA)-coated silica (pNA-sil) was characterized by Fourier transform infrared spectroscopy (FT-IR), elemental analysis (EA), and nitrogen sorption porosimetry (NSP). Then the pNA-sil was packed into the stainless-steel column and evaluated in high-performance liquid chromatography (HPLC). Good chromatographic performance for the separation of peptides and nucleosides was obtained under HILIC mode. The results indicated that the pNA-sil stationary phase behaved as mixed-mode retention mechanisms of hydrophilic and ionic interactions. Furthermore, the pNA-sil phase was used to separate tryptic digest of ß-casein and our results showed that more than 12 peptides peaks were resolved and well distributed within the elution window. Finally, the pNA-sil stationary phase was demonstrated to possess remarkable reproducibility and stability. Taken together, the pNA-sil stationary phase prepared in the current study offers a potential application in proteomics study.

Rapid and high-throughput determination of cationic surfactants in environmental water samples by automated on-line polymer monolith microextraction coupled to high performance liquid chromatography-mass spectrometry.

A rapid, high throughput and sensitive method was presented for automated determination of cationic surfactants in environmental water samples. The method was based on an automated analysis platform that was composed of on-line polymer monolith microextraction (PMME) and high performance liquid chromatography-mass spectrum (HPLC-MS) with an autosampler. A poly(methacrylic acid-co-ethylene dimethacrylate) (MAA-co-EDMA) monolith was selected as the sorbent for purification and enrichment of cationic surfactants in environmental water samples while a new mixed-mode chromatographic column packed with octyl and sulfonic acid co-bonded silica (OSS) was employed for separation and quantitative determination of cationic surfactants in water samples. By integrating sample preparation, chromatographic separation and MS detection into one automated platform, it makes the whole analysis procedure simple, accurate, and time and labor-saving. Several parameters affecting the extraction performance were investigated. Under the optimized conditions, the proposed method was applied to the analysis of seven cationic surfactants in environmental water samples. Good linearities were obtained for all cationic surfactants with R² larger than 0.9895. The limits of detection were found to be in the range of 15-24 ng/L. The method recoveries of the cationic surfactants spiked in water samples were from 80.5% to 115.1%, with relative standard deviations less than 12.4%.